$10K Drag Shootout 2:  Engine Profile — Midwest Mayhem

$10K Drag Shootout 2: Engine Profile — Midwest Mayhem

A group of friends who race together an extreme amount (by “normal” people’s standards), Team Midwest Mayhem has a very impressive level of combined knowledge and experience. After the vehicle-choice round of competition, the midwesterners wound up with the G-body — which definitely has a street-racing pedigree — in the form of a 1979 Oldsmobile Cutlass.

While the G-body offers tons of room in the engine bay for all sorts of activities, Midwest Mayhem opted for a compact LS engine. Not only is their bullet of choice physically compact, but it’s also the smallest-displacement engine of the competition.

Mighty Mouse

While 75-percent of the teams in the competition have chosen the LS engine, Midwest Mayhem team-leader and engine-guy, Joe Hunt, opted for the smallest 4.8-liter variant. Not only is the team relying on their turbocharger to be the replacement for displacement, but they are taking the whole “stock bottom end” thing to the extreme.

The team has a good reason for going with the 4.8-liter. They didn’t just pick up any old LS engine out of a junkyard; instead, they scored a Gen-IV 4.8-liter for $200. The Gen-IV LS engines have improved connecting rods and the cast 4.8-liter cranks are documented to hold horsepower in the four-digit range.

With that in mind, the only thing Hunt touched in the OEM short-block, were the piston rings. For those, Hunt went with a set of Total Seal CR-series (Classic Race) rings, opened up a bit to account for the boost they will be shoving into the engine.

Team Midwest Mayhem is taking “stock bottom end” to the extreme, with the short-block of their 4.8-liter Gen-IV LS exactly the way it came out of the donor vehicle — except for new piston rings from Total Seal.

The Total Seal rings are a standard 1.5mm, 1.5mm, 3.0mm set. The top ring is a ductile-iron ring with a plasma-moly coating, while the second ring is a conventional cast-iron ring. A standard-tension, stainless-steel oil ring rounds out the only modifications made to Midwest Mayhem’s rotating assembly.

While OEM bearings were used in both the mains and rods, Hunt did opt for a set of ARP main studs to reassemble the engine with. For those of you counting, that means only two new parts used in the entirety of the bottom half of the team’s engine.

OEM-ish Top End

You’d think with all the saved budget from the short-block, Midwest Mayhem might be a little extravagant on the top half of the engine. Instead, the team’s frugality extends to the heads and intake as well, although, not quite as stringently as with the bottom-end.

Since the Gen-IV 4.8-liter engines came from the factory with what are regarded as the premier cathedral-port castings (799s) the team simply took a die-grinder to the intake and exhaust ports to give them a little extra airflow. The original 2.00-inch intake and 1.55-inch exhaust valves are also run as fitted from the factory.

However, Hunt and company did splurge a little on a Brian Tooley Racing Platinum Valvespring Kit. Composed of dual valvesprings with a combined spring rate of 409 lb/in, titanium retainers, and steel 7-degree locks, the kit also comes with locators for the stock valve-guides.

To fit the upgraded 3/8-inch pushrods, Joe Hunt had to clearance the factory 799 cylinder heads. An endmill chucked up in a cordless drill may not be the prettiest method of machining, but it was quick, and it worked.

Continuing the theme, the original rocker arms were used with no upgrades. A custom-ground COMP Cams bumpstick is used, as it was provided free of charge to all competitors. The team stuck with hydraulic-roller lifters, but upgraded to COMP’s short-travel race lifters. The new lifters are REM-finished to minimize friction and designed to limit internal travel to maximize high-RPM performance.

Connecting the lifters and the rocker arms are a set of upgraded Brian Tooley Racing 3/8-inch-diameter, 7.375-inch-long pushrods For the timing set, Midwest Mayhem simply opted for an upgraded Chevrolet Performance 58X timing sprocket and new Summit Racing LS2 single-roller timing chain.

Covering the valvetrain are a pair of Moroso‘s billet LS valve covers. Designed to clear most aftermarket valvetrains, the tall covers from Moroso provide an oil fill port on each of the valve covers in addition to mounting points for the LS coils which will be used.

ARP head studs were chosen to hold the heads in place for their superior clamping force, while a set of Brian Tooley Racing multi-layer steel head gaskets were used to seal the combination’s heads to the block.

Getting Wired

While externally, the team’s stock, plastic 4.8-liter intake suggests more frugality, that notion ends once the other hardware comes to light. Fitted to the plastic intake is a set of DeatschWerks 1,000 cc/minute fuel injectors, along with a 92mm Holley Sniper EFI throttle body. With the choice of VP Racing Fuels C16 race gas or X85 race-blend ethanol, Hunt decided to stick with the more traditional C16 as their fuel of choice.

Providing fuel to the injectors is a used MagnaFuel ProTuner 750-series external pump the team scored for $175. Summit Racing fuel filters and pressure regulator, along with a Holley fuel rail kit, all plumbed together with Fragola hoses and fittings complete the fuel system.

For the ignition side of the equation, the team went with LS coil packs from E3 Spark Plugs, Summit Racing 8.5mm spark plug wires, and E3-108 spark plugs. Managing both the fuel and spark is one of Holley’s Terminator X engine-management systems designed to make an LS swap a plug-and-play affair, but with all the control of Holley’s more advanced ECU systems.

All of the LS engines in the competition are running E3 LS coils and E3 spark plugs to provide all of the spark energy they’ll need to keep the candles lit under the severe cylinder pressures they’ll see. While billet valve covers with a stock intake manifold might seem like opposite ends of budgetary spectrum, Moroso provided the covers outside of the teams’ budgets.

For Team Midwest Mayhem’s power-adder, they opted for a BorgWarner AirWerks SX400 80mm turbocharger, identical to the one chosen by Team Enemies Everywhere. The 80mm cast-aluminum compressor wheel is spun by a 96mm exhaust turbine wheel. The 1.32 A/R ratio provides a stout top end, but will potentially be a bit slow to spool on the smaller-displacement engine of Midwest Mayhem.

Also differing from the other team using the same turbocharger, Hunt opted for a Summit Racing universal aluminum air-to-air intercooler. It features 3-inch inlets and outlets, and a 31-inch by 12-inch core with a 4-inch core-thickness, plumbed with Spectre Performance aluminum tubing.

The team also opted for a blow-off valve on the inlet, in the form of a used eBay-special 50mm unit. To control the boost, a used, unknown-make 44mm wastegate was sourced for the princely sum of $55. The hot side was constructed using OEM 4.8-liter manifolds, and mandrel-bent steel tubing from Diamond Eye Performance.

While an unconventional engine build strategy, we’re curious to see how Team Midwest Mayhem’s plan of attack plays out on the racetrack.

Opting for an 80mm BorgWarner AirWerks SX400 turbo with a Summit Racing air-to-air intercooler, the team found an interesting mounting location in the G-body’s passenger-side headlight opening.

Team Midwest Mayhem Spec Sheet

Team: Midwest Mayhem
Engine:  Gen-IV LS
Total Displacement: 293.3 cubic inches
Bore x Stroke: 3.780 inches x 3.267 inches
Block: OEM 4.8L
Crankshaft: OEM 4.8L
Main Bearings: OEM 4.8L
Rod Bearings: OEM 4.8L
Rods: OEM 4.8L
Pistons: OEM 4.8L
Rings: Total Seal CR-series 1.5mm, 1.5mm, 3.0mm
Oil Pump: OEM 4.8L
Oil Pan: OEM 4.8L
Timing Set: Chevrolet Performance 58X sprocket, Summit Racing single-roller chain
Cylinder Heads: OEM 799 casting
Port Work: Hand ported
Head Gaskets: Brian Tooley Racing MLS
Valves: OEM 4.8L; 2.00-inch intake, 1.55-inch exhaust
Valvesprings: Brian Tooley Racing dual 409 lb/in
Locks/Retainers: Titanium retainers, 7-degree steel locks
Camshaft: COMP Cams custom hydraulic roller
Lifters: COMP Cams hydraulic roller short travel
Rockers: OEM 4.8L
Pushrods: Brian Tooley Racing 3/8-diameter, 7.375-inch (used)
EFI System: Holley Terminator-X
Injectors: DeatschWerks 1,000 cc/min
Throttle Body: Holley Sniper EFI 92mm
Intake Manifold: OEM 4.8L
Headers: OEM 4.8L
Power Adder: Borg Warner AirWerks 80mm turbocharger, 1.32 A/R
Coil Packs: E3
Spark Plugs: E3-108
Plug Wires: Summit Racing 8.5mm
Fuel Pump: MagnaFuel ProTuner 750 (used)

 

About the author

Greg Acosta

Greg has spent nineteen years and counting in automotive publishing, with most of his work having a very technical focus. Always interested in how things work, he enjoys sharing his passion for automotive technology with the reader.
Read My Articles

Horsepower delivered to your inbox.

Build your own custom newsletter with the content you love from EngineLabs, directly to your inbox, absolutely FREE!

Free WordPress Themes
EngineLabs NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

EngineLabs

EngineLabs

We'll send you raw engine tech articles, news, features, and videos every week from EngineLabs.

EngineLabs

EngineLabs NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

EngineLabs

EngineLabs

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...


LSX Mag
Late Model LS Vehicles
Dragzine
Drag Racing
StreetMuscle
Muscle Car & Hot Rods

EngineLabs

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...

  • LSX Mag Late Model LS Vehicles
  • Dragzine Drag Racing
  • Street Muscle Mag Muscle Car & Hot Rods

EngineLabs

EngineLabs

Thank you for your subscription.

Thank you for your subscription.

EngineLabs

Thank you for your subscription.

Thank you for your subscription.

Loading