Temu Vortec Heads: A Bargain Or Mistake? Weingartner Racing Finds Out

Jimmy Stray
•
November 17, 2026

You might want to grab some popcorn because things get interesting when Eric Weingartner of Weingartner Racing takes a closer look at a set of Temu Vortec heads for a small-block Chevy. At just $350 delivered for the fully assembled pair, the price alone is enough to raise a few eyebrows. The heads belong to a customer who bought them on a whim through Temu. Weingartner said they weighed roughly 40 pounds each, making the delivered price even more surprising. He wasn’t about to judge them on price alone. He lined them up against familiar Vortec castings, checked the valves, pulled them apart, and put one on the flow bench.

The First Look At Temu Vortec Heads

For a visual reference, Weingartner used a factory GM 906 Vortec head and an aftermarket EQ Vortec-style casting. From the intake and exhaust sides, the Temu heads looked reasonably close. The intake openings weren’t exact, but the exhaust ports resembled the originals.

That all changed when Weingartner flipped the heads over to examine the combustion chambers. “What in the China is this?” he exclaimed. Compared with the factory 906 and aftermarket castings, the Temu chambers were dramatically different, with crude, squared-off shapes that barely resembled the original Vortec design. “It’s like they just made everything square,” he said, describing the chambers as “hideous” and “horrible.” He also pointed out differences in the spacing around the combustion chambers and questioned whether the heads would seal properly. The comparison with the aftermarket EQ castings only made the shortcomings of the Temu combustion chambers more apparent.

 Side-by-side combustion chamber comparison: Temu Vortec cylinder head (left) and factory GM 906 Vortec head (right)
Side-by-side combustion chamber comparison: Temu Vortec cylinder head (left) and factory GM 906 Vortec head (right)

Four Exhaust Ports Pass, Four Intakes Fail

Using the vacuum tester on his seat-and-guide machine, Weingartner checked how well the valves sealed. All four exhaust ports passed, but the intake side was a completely different story. All four intake ports failed the vacuum check. “That ain’t passing. That ain’t even close to passing,” Weingartner remarked after testing the first intake port. After removing the valves, Weingartner found them coated with Cosmoline, a rust preventative. He suspected the coating might be preventing the valves from seating properly, especially with the weak valve springs. However, he didn’t clean and retest them, so the exact cause of the sealing failures remains unconfirmed.

The valve job gave Weingartner even more reasons to criticize the heads. The intake valves lack back cuts, and the intake seats had an unusually wide 45-degree angle. The exhaust side wasn’t much better, with only a 45-degree basic seat cut and a square transition. Further inspection revealed sharp edges and abrupt transitions through the ports, along with the short-side turn that lacked a smooth radius. Based on the port geometry, Weingartner doubted these heads could flow as much air as an ordinary stock small-block Chevy head, let alone a factory Vortec casting.

Temu Vortec cylinder head showing an intake valve without a back cut and an unusually wide 45 degree  seat cut
Temu Vortec cylinder head showing an intake valve without a back cut and an unusually wide 45-degree seat cut

Springs, Clearance, and Camshaft Limits

The problems weren’t limited to the castings and valve jobs. Weingartner measured approximately .477 inches between the valve spring retainer and valve seal. Subtracting his preferred .060-inch safety margin left only about .420 inch of usable valve lift. That severely limits camshaft selection, since exceeding the available clearance would cause the retainer to contact the valve seal.

He also checked the valve springs. At an installed height of 1.753 inches, they produced 102 pounds on the seat and 262 pounds open. Weingartner considered those figures acceptable for a hydraulic flat-tappet cam, but insufficient for a solid flat-tappet or hydraulic roller applications. Regardless of spring capabilities, the limited retainer-to-seal clearance is a big problem. Simply arriving fully assembled didn’t make these heads ready for every application.

Temu Vortec Heads On The Flow Bench

Flow bench testing provides valuable information about a cylinder head’s airflow characteristics, but peak CFM numbers don’t tell the entire story. As we’ve discussed in our previous article, Going With The Flow: We Discuss Flowbench Uses And Misconceptions, understanding the results requires looking beyond the highest number.

Temu Vortec cast-iron cylinder head mounted on a flow bench for airflow testing at Weingartner Racing.
Temu Vortec cast-iron cylinder head mounted on a flow bench for airflow testing at Weingartner Racing.

After examining the questionable port geometry, Weingartner put one of the heads on his flow bench using a 4.030-inch bore fixture. The results were even worse than he anticipated. Airflow at low valve lift was so poor that he had to change the bench’s measurement range to obtain readings. At .100-inch valve lift, the intake port managed just 30 cfm. Weingartner explained that he normally expects a Vortec-style head to flow approximately 60 to 70 cfm at that lift. At .200 inch, airflow increased to 71 cfm, well below the 115 to 120 cfm he generally expects. The intake reached 125 cfm at .300 inch and 174 cfm at .400 inch. At .500-inch of valve lift, airflow finally reached 207 cfm, comparable to the peak airflow of an older GM 882 casting. However, the relatively respectable peak airflow doesn’t make up for the extremely poor flow at lower valve lifts.

The exhaust results weren’t particularly encouraging either. At .100-inch lift, the exhaust port flowed 40 cfm, compared with just 30 cfm on the intake side. At .200-inch lift, the exhaust continued to outperform the intake, flowing 83 cfm compared to the intake’s 71 cfm. Exhaust flow eventually reached 138 CFM at .500-inch lift, but Weingartner was particularly critical of the poor airflow at lower valve lifts. The retainer also contacted the valve seal at .520-inch lift, confirming the limited clearance measured during the earlier inspection.

Flowbench results for the Temu Vortec cylinder head, comparing intake and exhaust air flow in CFM at valve lifts from .100 to .550 inch
Flowbench results for the Temu Vortec cylinder head, measuring intake and exhaust air flow in CFM at valve lifts from .100 to .550 inch

Worth the Price?

For $350 delivered, the buyer received two fully assembled cast iron Vortec-style cylinder heads. Unfortunately, the inspection revealed a long list of problems, including poorly shaped combustion chambers, four intake ports that failed vacuum testing, questionable valve-seat machining, restrictive port geometry, inadequate clearance for higher-lift camshafts, and exceptionally poor low-lift airflow.

Weingartner didn’t attempt to conceal his disappointment. He considered this particular set the worst new cylinder heads he had ever examined and explicitly recommended against buying them. Although the heads were never installed on an engine or tested on a dynamometer, the inspection and flow-bench results provide more than enough evidence to explain his assessment.

The Temu Vortec heads may have an attractive price tag, but based on what Weingartner found, their low cost comes with some serious compromises. Sometimes a bargain just isn’t worth the trouble.